# Columbus Repipe Cost Calculator

> Free repipe cost calculator for Columbus, Upper Arlington, Bexley and Grandview Heights: typical ranges by pipe, permit lines and what moves the price.

URL: https://slaterepipingcolumbus.com/tools/repiping-cost-estimator/

Free tool

This repipe cost calculator gives a Columbus-area budget for replacing the water supply piping in a house or a larger building, with the permit lines for your city and the drivers behind the number. No contact details needed, and the result changes as you answer.

Free tool

This repipe cost calculator gives a Columbus-area budget for replacing the water supply piping in a house or a larger building, with the permit lines for your city and the drivers behind the number. No contact details needed, and the result changes as you answer.

## Estimate your house

Five answers. The range depends only on the building, how much of it is repiped and the pipe; the permit is shown as its own line, so you can see what each part of the cost is.

## How the estimate works

The ranges are typical Columbus-area ranges for a whole-house repipe, drawn from local project figures. They are budgeting figures, not the contractors' rates and not a quote. No answer you give stretches them: there are no multipliers and no square-foot scaling, and the upper end stays open where larger or more finished houses run past it.

The permit lines come from the [City of Columbus Building and Zoning Services fee schedule](https://www.columbus.gov/files/sharedassets/city/v/14/bzs/fee-schedule/2026-combined-development-related-fee-schedule.pdf) and the [Franklin County Public Health plumbing fees](https://myfcph.org/fiscal-services/#feeschedules). The county permit line is the only arithmetic: its fee plus the per-fixture charge times the fixture count you choose.

For context on labor: the Bureau of Labor Statistics puts the median wage for plumbers in the Columbus metro at $30.41 an hour, about the same as the $30.67 national median ([Columbus metro](https://www.bls.gov/oes/current/oes_18140.htm), [United States](https://www.bls.gov/oes/current/oes472152.htm)). A wage is not a billing rate, which also carries insurance, licensing, vehicles and overhead.

## What you get for each house

| Your answers | The estimator shows |
| --- | --- |
| Whole house, double or triplex, material not decided | $4,000 to $15,000+, a typical Columbus-area range. |
| Whole house with PEX | $4,000 to $12,000, a typical Columbus-area range for PEX. |
| Whole house with copper | $6,000 to $18,000+, a typical Columbus-area range for copper. |
| 4 or more units, commercial or mixed-use | No range. The drivers for that building, and a price after a walk-through. |
| Any partial repipe | No range. Which lines are replaced and where new meets old decide the price. |

### Never inside the range

- The permit, shown as its own line ($275 for a house in the City of Columbus)
- A new water heater, and new fixtures
- Patching and painting, unless the quote lists it
- Sewer and drain lines, which are a separate trade
- The water service line from the street

[Read the Columbus repipe cost guide](https://slaterepipingcolumbus.com/guide/repiping-cost/)[Not sure you need a repipe? Take the check](https://slaterepipingcolumbus.com/tools/repiping-assessment/)[Compare quotes with the printable checklist](https://slaterepipingcolumbus.com/resources/)

## Questions about the estimator

### Why does the estimator give a range for a house but not for an apartment building?

A range is published only where local project figures support one: $4,000 to $15,000+ for a whole-house repipe of a house, double or triplex, $4,000 to $12,000 with PEX and $6,000 to $18,000+ with copper. A building with 4 or more units, a commercial building or a partial repipe varies too much with risers, occupied units and access, so the estimator shows what drives the price and leaves the number to a walk-through.

### Does the Columbus permit fee go up with the size of the repipe?

Not for a house. Building and Zoning Services charges a flat $275 plumbing permit for a 1, 2 or 3 family dwelling, with 2 inspections included and $225 for each extra trip. For 4 or more units the permit is $550 or $700, and a full system replacement adds plan review billed by the hour.

### Why is the permit different in Upper Arlington, Bexley or Grandview Heights?

Plumbing plan review and inspection in those cities go through Franklin County Public Health, which charges $135 plus $80 an hour for plan review and a $135 permit fee plus $20 per fixture. That is why the estimator asks for a rough fixture count.